Electric Drive SCADA Development with Vijeo Designer (Schneider Electric)

Authors

  • Oleksandr Aksonov O. M. Beketov National University of Urban Economy in Kharkiv
  • Vladyslav Pliuhin O. M. Beketov National University of Urban Economy in Kharkiv
  • Yevgen Tsegelnyk O. M. Beketov National University of Urban Economy in Kharkiv
  • Oleksii Slovikovskyi National University of Life and Environmental Sciences of Ukraine
  • Oleksii Duniev National Technical University "Kharkiv Polytechnic Institute"
  • Andrii Yehorov National Technical University "Kharkiv Polytechnic Institute"

DOI:

https://doi.org/10.33042/2079-424X.2022.61.3.04

Keywords:

human interface device, SCADA, electric drive, Vijeo Designer, control panel, control system, remote control

Abstract

The paper is devoted to the disclosure the construction of the SCADA system for managing the operating modes and monitoring the electric drive of the overhead crane. The material is provided in the form of step-by-step instructions for building such a system in the Vijeo Designer program. The creation of a new project, interface elements, binding variables with interface elements, setting the behavior of dynamic interface elements are shown in detail. The issue of communication of global variable visual elements of the interface with the M241 controller and the program in SoMachine has been revealed. The developed interface allows to control three mechanisms of the bridge crane: main hoist, auxiliary hoist and carriage movement. It is shown how to control frequency converters that are connected to the controller through different types of communication: direct analog to the controller, and through the Ethernet/IP protocol. The work will be useful for academic purposes in teaching students as well as for researchers and industrial engineers.

Author Biographies

Oleksandr Aksonov, O. M. Beketov National University of Urban Economy in Kharkiv

Postgraduate Student, Department of Urban Power Supply and Consumption Systems

Vladyslav Pliuhin, O. M. Beketov National University of Urban Economy in Kharkiv

D.Sc., Professor, Department of Urban Power Supply and Consumption Systems

Yevgen Tsegelnyk, O. M. Beketov National University of Urban Economy in Kharkiv

Ph.D., Senior Researcher, Department of Automation and Computer-Integrated Technologies

Oleksii Slovikovskyi, National University of Life and Environmental Sciences of Ukraine

Postgraduate Student, Department of Automation and Robotic Systems named by I. Martynenko

Oleksii Duniev , National Technical University "Kharkiv Polytechnic Institute"

Ph.D., Associate Professor, Department of Electrical Machines

Andrii Yehorov, National Technical University "Kharkiv Polytechnic Institute"

Ph.D., Associate Professor, Department of Electrical Machines

References

Hirankitti, V. (2023). An object-oriented agent framework for SCADA. In A.K. Nagar, D. Singh Jat, D.K. Mishra, A. Joshi (eds.) Intelligent Sustainable Systems. LNNS, vol. 579 (pp. 687–696). Springer. https://doi.org/10.1007/978-981-19-7663-6_65

Hirankitti, V. (2019). An intelligent agent frame-work for SCADA. In 2019 First International Conference on Digital Data Processing (DDP) (pp. 76–81). IEEE. https://doi.org/10.1109/DDP.2019.00024

Popescu, V.F., Gânsac, V., Comşa, O., Pârvu, M., & Pistol, S. (2022). Supervisory Control and data acquisition (SCADA) traffic simulation for controlling industrial processes and infrastructures. Land Forces Academy Review, 27(4), 423–440. https://doi.org/10.2478/raft-2022-0051

Kibulungu, J.W., Laseinde, O.T. (2023). Automatic control system based on Industry 4.0, PLC, and SCADA. In A.K. Nagar, D. Singh Jat, D.K. Mishra, A. Joshi (eds.) Intelligent Sustainable Systems. LNNS, vol. 578 (pp. 183–197). Springer. https://doi.org/10.1007/978-981-19-7660-5_16

Kiangala, K.S., & Wang, Z. (2019). An Industry 4.0 approach to develop auto parameter configuration of a bottling process in a small to medium scale industry using PLC and SCADA. Procedia Manufacturing, 35, 725–730. https://doi.org/10.1016/j.promfg.2019.06.015

Merchan, D.F., Peralta, J.A., Vazquez-Rodas, A., Minchala, L.I., & Astudillo-Salinas, D. (2017). Open source SCADA system for advanced monitoring of industrial processes. In 2017 International Conference on Information Systems and Computer Science (INCISCOS) (pp. 160–165). IEEE. https://doi.org/10.1109/INCISCOS.2017.9

Fitriani, S., & Sofyan, Y. (2020). Simulator human machine interface (HMI) using visual basic on the SCADA system. IOP Conference Series: Materials Science and Engineering, 830(3), 032016. https://doi.org/10.1088/1757-899X/830/3/032016

Almas, M.S., Vanfretti, L., Løvlund, S., & Gjerde, J.O. (2014). Open source SCADA implementation and PMU integration for power system monitoring and control applications. In 2014 IEEE PES General Meeting| Conference & Exposition (pp. 1–5). IEEE. https://doi.org/10.1109/PESGM.2014.6938840

Endi, M., & Elhalwagy, Y. (2010). Three-layer PLC/ SCADA system architecture in process automation and data monitoring. In 2010 the 2nd international conference on computer and automation engineering (Vol. 2, pp. 774–779). IEEE. https://doi.org/10.1109/ICCAE.2010.5451799

Padhee, S., & Singh, Y. (2011). Data logging and supervisory control of process using LabVIEW. In IEEE Technology Students' Symposium (pp. 329–334). IEEE. https://doi.org/10.1109/TECHSYM.2011.5783838

Hafeez, S.M., & Ghauri, Y.J. (2014). Supervisory control and FPGA based DAQ card. Applied Mechanics and Materials, 666, 64–68. https://doi.org/10.4028/www.scientific.net/AMM.666.64

Kumar, N., & Kumar, U. (2012). Simulation of virtual SCADA system using LabVIEW. In 2012 IEEE 5th India International Conference on Power Electronics (pp. 1–5). IEEE. https://doi.org/10.1109/IICPE.2012.6450456

Sita, I.V. (2012). Building control, monitoring, safety and security using collaborative systems. In 2012 Fourth International Conference on Intelligent Networking and Collaborative Systems (pp. 662–667). IEEE. https://doi.org/10.1109/iNCoS.2012.107

Marosan, A.I., Constantin, G., Barsan, A., Crenganis, M., & Girjob, C. (2020). Creating an ethernet communication between a Simatic S7-1200 PLC and Arduino Mega for an omnidirectional mobile platform and industrial equipment. IOP Conference Series: Materials Science and Engineering, 968, 012022). https://doi.org/10.1088/1757-899X/968/1/012022

Electric, S. (2014). Schneider Electric: Estratégia SCADA para os Próximos Três Anos. Neutro à Terra, (14), 61–64. https://doi.org/10.26537/neutroaterra.v0i14.420

Fandidarma, B., Sunaryantiningsih, I., & Pratama, A. (2022). Pengatur suhu ruangan tertutup menggunakan PLC Schneider TWIDO COMPACT berbasis SCADA-WONDERWARE INTOUCH. ELECTRA: Electrical Engineering Articles, 2(2), 01-11. https://doi.org/10.25273/elec

tra.v2i2.12246

Yang, B., Qiao, L., Zhu, Z., & Wulan, M. (2016). A metamodel for the manufacturing process information modeling. Procedia CIRP, 56, 332-337. https://doi.org/10.1016/j.procir.2016.10.032

Haba, S.A., Oancea, G. (2023). Study on design and manufacturing of an engine block using digital tools. In P. Kyratsis, A. Manavis, J.P. Davim (eds.) Computational Design and Digital Manufacturing. MINEN (pp. 167–203). Springer. https://doi.org/10.1007/978-3-031-21167-6_9

Querejeta, M.U., Etxeberria, L., & Sagardui, G. (2021). Virtual commissioning in machine tool manufacturing: a survey from industry. DYNA, 96, 612–619. https://doi.org/10.6036/10244

Lechler, T., Fischer, E., Metzner, M., Mayr, A., & Franke, J. (2019). Virtual commissioning – Scientific review and exploratory use cases in advanced production systems. Procedia CIRP, 81, 1125–1130. https://doi.org/10.1016/j.procir.2019.03.278

Aksonov, Y., Tsegelnyk, Y., Piddubnyi, O., Kombarov, V., Plankovskyy, S., & Piddubna, L. (2022). Interactive design of CNC equipment operator panels. International Journal of Mechatronics and Applied Mechanics, 2022(12), 156–162. https://doi.org/10.17683/ijomam/issue12.23

Zhang, P. (2010). Human-machine interfaces. In Advanced Industrial Control Technology (pp. 527–555). William Andrew. https://doi.org/10.1016/B978-1-4377-7807-6.10013-0

Gong, C. (2009). Human-machine interface: Design principles of visual information in human-machine interface design. In 2009 International Conference on Intelligent Human-Machine Systems and Cybernetics (Vol. 2, pp. 262–265). IEEE. https://doi.org/10.1109/IHMSC.2009.189

Massaro, A. (2021). Human–machine interfaces. In Electronics in Advanced Research Industries. John Wiley & Sons. https://doi.org/10.1002/9781119716907.ch3

Schneider Electric. (2014). Vijeo Designer Tutorial.

Sărăcin, C.G., Deaconu, I.D., & Chirilă, A.I. (2019). Educational platform dedicated to the study of program-mable logic controllers and the human-machine interface. In 2019 11th International Symposium on Advanced Topics in Electrical Engineering (ATEE) (pp. 1–4). IEEE. https://doi.org/10.1109/ATEE.2019.8725021

Downloads

Published

2022-12-30

How to Cite

Aksonov, O., Pliuhin, V., Tsegelnyk, Y., Slovikovskyi, O., Duniev , O., & Yehorov, A. (2022). Electric Drive SCADA Development with Vijeo Designer (Schneider Electric). Lighting Engineering & Power Engineering, 61(3), 107–121. https://doi.org/10.33042/2079-424X.2022.61.3.04

Issue

Vol. 61 No. 3 (2022): Lighting Engineering & Power Engineering

Section

Power Engineering

License

Copyright (c) 2023 Lighting Engineering & Power Engineering

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

The authors that are published in this journal agree with the following terms:

  • The authors reserve the right of authorship of his work and pass to the journal the right of first publication of this work is licensed under a Creative Commons Attribution License, which allows others to freely distribute published work with reference to authors of original works and works first published in this journal.
  • The authors have the right to enter into a separate additional agreement for non-exclusive distribution of work in the form in which it was published in the magazine (for example, to place work in electronic storage agencies or publish as part of the monograph), providing the reference to the first publication in this journal.
  • Journal policy allows and encourages the placement by the authors on the Internet (eg, in storage facilities or personal websites) the manuscript of the works before the submission of the manuscript to the editor as well as during its editorial processing, as it contributes to productive scientific discussion and has a positive impact on efficiency and dynamics citing published work (see. The Effect of Open Access).